(1)for any explanations on the operations of the projector mode, the electronic pen will be referred to as "mouse" ccalibration
(2)alibration is an operation to calibrate the position of the computer screen projected onto the interactive panaboard screen to judge the position by the interactive panaboard software.
start the interactive panaboard software and select the projector mode. (see page 29.)
(1) in the sequence of upper left, upper right, lower right and lower left, press for about two seconds for center of each four corner position with the electronic pen.
when this operation ended correctly, then the next position starts automatically.
(2) when the calibration ended correctly, there is a message telling you its finish. from this point onward, the electronic pen can be used as the mouse.the calibration screen is displayed.and the projected computer screen on the interactive panaboard will be referred to as "desktop".
(1)if you move the projector or interactive panaboard, the position of the computer screen projected onto the interactive panaboard screen will be changed. this will result in out of position of the electronic pen. if this happens, you will need to recalibrate the unit by executing [calibrate] in the pop-up menu.
(2)in the projector mode, use the electronic pen with its cap on.
(3)do not cover the position receiver with your hand as this may cause interactive function to stop functioning.
(4)press down firmly with the point of the electronic pen on the screen film until you hear a buzzing sound.
(5)for precise positioning, keep the electronic pen perpendicularly to use the interactive panaboard screen during use. inclined pen angle will cause the shift of position.
if recalibration is necessary, click [calibrate] in the pop-up menu.
1 use the electronic pen as a mouse
after the calibration is completed, the electronic pen can be used as a mouse for the projected computer screen on the interactive panaboard.
(1)single click: press the projected screen with the tip of the electronic pen.
(2)double-click: double-click is executed by performing two quick clicks at the same position with the tip of the electronic pen.
(3)drag: press and hold the desire image with the tip of the electronic pen while dragging the image to its new position.
(4)right-click: locate light gray button on the electronic pen. while pressing the button of the electronic pen, press the projected screen with the tip of the electronic pen and release. (do not release the button of the electronic pen before all of these operations are finished.) for more details about the desktop drawing tools, please refer to "about desktop drawing tool" from page 36.
remark:if double-click does not work properly, confirm that the same position is accurately clicked twice. when the position is different, it is not recognized a double click.or, try different timing of depressing and releasing of the electronic pen. this operation is also depending on the setting of the double-click speed of the [control panel].
for precise positioning, keep the electronic pen perpendicularly to the interactive panaboard screen
2 draw and erase handwritten lines on the desktop
remark:the width and color of the markers and the size of the eraser can be changed. (see page 38.)
3 record image and handwritten lines data on the desktop
data of handwritten lines drawn or erased on the desktop using the desktop drawing tool can be recorded in interactive panaboard format files (extension ".ipb", referred to as ipb documents) along with the initial desktop image. written or erased handwritten lines are recorded in stroke units and can be displayed, played back and edited later in the view window.
①ifthere are drawn lines on the desktop, a verification dialog box will appear to confirm whether to erase drawings. to erase the drawn lines and start recording, click [yes] button. to leave the drawn lines and start recording, click [no] button. in this case, drawn lines become apart of background image.
②the image of the desktop is displayed in the dialog box.
(2)if it is acceptable to store as a background image, click the [ok] button.
(5) click the [ok] button to record the recording image.
①the save as dialog box will appear.
(6) enter the folder where you want to save the file and the file name.
①the extension of the file is ".ipb".
(7) click the [save] button.
more than one page can be recorded. (see page 40.)
remark:do not change the desktop resolution while recording data. if changed, the desktop image will not be
displayed properly when it is displayed in the view window.
4 playback the recorded data by view window
desktop background data and handwritten lines data stored using the desktop drawing tool can be displayed in the view window as well as browsed, played back and edited.
(2) click [open...] in the [file] menu.
the open dialog box will appear.
(3) enter the folder to look in and the file name you want to open.
the file has an ".ipb" extension.
(4) click the [open] button.(2) click [open...] in the [file] menu.
the open dialog box will appear.
(3) enter the folder to look in and the file name you want to open.
the file has an ".ipb" extension.
(4) click the [open] button.
remark:many different operations can be executed in the displayed ipb document. save the ipb document in another file format. (see page 50.) switch a page of the ipb document. (see page 54.) edit a page of the ipb document. (see page 54.) playback the ipb document. (see page 57.) print the ipb document. (see page 58.)