the blinking item is the one selected.
if the following error occurs frequently, change the setting by referring to the explanation on the table.
1 double-feed
2 mis-pick
3 paper jam1
2. setting pre-pick
3. setting pick speed
the blinking item is the one selected.
pick roller rotation speed should be set slow for scanning thin or soft documents, these documents tend to cause a mis-pick to occur.
when the pick speed is set at "mid" or "slow", the scanner will slow down.
4. setting double-feed detection (document thickness)
(1) [no] is blinking: document thickness is not checked.
(2) [yes] and [1] are blinking: document thickness is checked.
however, scanning continues even if double- feed is detected and the error message is displayed on the lcd.
(3) [yes] and [2: stop] are blinking: document thickness is checked.
when double-feed is detected, scanning stops. then the error is reported to the pc.
the blinking item is the one selected.
(1) [thickness] is blinking: double-feed is detected by light amount transmitted through paper.
(2) [thickness & roller] is blinking: double-feed is detected based on the light amount transmitted through paper and brake roller rotation amount.
(1) [pick] is blinking: double-feed is checked by the document pick timing.
(2) [pick & feed] is blinking: double-feed is checked by the document pick timing and during feeding.
1 double-feed detection accuracy increases when both thickness and length of documents are checked.
2 when a double-feed is detected and the scanning operation is stopped, the last documents in the hopper or the one ahead of it might have been double fed.
3 depending on the document type, there are cases when double-feed can not be detected.
5. setting double-feed detection (by document length)
(1) [no] is blinking: document length is not checked.
(2) [yes] and [1] are blinking: document length is checked.
however, scanning continues even if double- feed is detected and the error message is displayed on the lcd.
(3) [yes] and [2: stop] are blinking: document length is checked. when double-feed is detected, scanning stops. then the error is reported to the pc.
the blinking item is the one selected.
(1) [10] is blinking: the document length difference below 10mm is not detected as an error.
(2) [15] is blinking: the document length difference below 15mm is not detected as an error.
(3) [20] is blinking: the document length difference below 20mm is not detected as an error.
6. setting skew check
7. setting ipc pre-set
the blinking item is the one selected.
when scanning in binary mode (line art), documents type and suitable pre-set pattern relationship is shown as follows:
1 the horizontal axis shows the darkness/color of the background against the text/lines on the documents.
2 the vertical axis shows the darkness of the text and lines on the documents.
一、document type and ipc preset pattern
*1 to 5 indicates ipc pre-set pattern number.
this setting is invalid in grayscale mode or in color mode. pre-sets are valid only in binary scan mode.
validity of each scan parameter when using ipc pre-set in offline mode, is shown in the following table.
二、validity of scan parameter
8. setting consumables replacement message
the blinking item is the one selected.
(1) [stop] is blinking: when the consumables replacement limit is reached, the consumables replacement message (abrasion alarm) is shown on the lcd and scanning stops.
(2) [message] is blinking: when the consumables replacement limit is reached, the consumables replacement message (abrasion alarm) is shown on the lcd but the scanning continues.
4) at [screen8-2], specify the number of scans to get consumables replacement message.
9. abrasion counter (abrasion cnt) reset
the blinking item is the one selected.
you can select a counter(s) from the following.
(1) [pick] is blinking: pick roller counter (pick cnt) can be reset.
(2) [brake] is blinking: brake roller counter (brake cnt) can be reset.
(3) [pad] is blinking: pad counter (pad cnt) can be reset.
(4) [f.lamp] is blinking: front-side lamp counter (front lamp) can be reset.
(5) [b.lamp] is blinking: back-side lamp counter (back lamp) can be reset.
[xxxxxx] indicates each abrasion counter value.
[xxxxxx] is the counter value of the selected consumable.
1 pick roller counter
2 brake roller counter
3 pad counter
4 front-side lamp counter (lamp-on time)
5 back-side lamp counter (lamp-on time)
10. setting short document scan mode(paper length setup)
the blinking item is the one selected.
(1) [normal] is blinking: this mode is for scanning documents longer than 80mm or 3.15inches.
(2) [short] is blinking: this mode is for scanning documents which length is 80mm or less, 3.15inches or less.
11. setting language
12. setting front-side background color
13. setting back-side background color
14. setting front-side dropout color
the blinking item is the one selected.
15. setting back-side dropout color
the blinking item is the one selected.
16. setting pick retry
the blinking item is the one selected.
17. setting feed retry
the blinking item is the one selected.
18. setting manual feed mode
the blinking item is the one selected.
pick start time can be specified by the unit of 0.2 second.
19. setting of scsi id
changed scsi id becomes valid after the scanner power is cycled.
20. setting of product id(scanner model number)
the blinking item is the one selected.
the following are the selectable product ids.
(1) fi4860c
(2) fi4990c
(3) m4099d
(4) m3099g
21. setting scsi bus width
the blinking item is the one selected.
- if 16 bit bus width data transfer is prohibited, specify [8] bit.
22. setting interface
the blinking item is the one selected.
available interface settings are as follows:
(1)[auto] is blinking: if an interface board, either from third party or optional, is installed in tps, this interface is used. if not, scsi interface is used.
(2) [scsi] is blinking: scsi interface is used. the interface on tps is disregarded.
(3) [tps] is blinking: tps interface is used. the scsi interface is disregarded.
23. setting baud rate of tps interface
the blinking item is the one selected.
baud rates available are as follows:
(1) 19200 bps
(2) 9600 bps
(3) 4800 bps
(4) 2400 bps
24. selection of imprinter
the blinking item is the one selected.
this screen is displayed when both of fi-486prfr and fi-486prre are installed.
25. setting imprinter numbering
to show your selection of imprinter or the imprinter to setup, [pre] or [post] is displayed.
the blinking item is the one selected.
initial number can be increased up to the maximum number (5digit: 99,999/ 8digit: 16,777,215).
command from the pc takes the priority over the setting from the operator panel.
26. reset the ink remain counter of imprinter.
if the following message comes up, prepare the new print cartridge. if no further printing is impossible, replace the print cartridge and reset the ink counter. if the print cartridge is replaced before print cartridge error occurs, be sure to reset the ink remain counter.
[xxxx] is the scanned sheet counter value.
in [xxxx], [pre] or [post] is displayed.
27. setting power save mode
the blinking item is the one selected.
a minimum of 5 minutes to the maximum of 60 minutes can be selected with 5 minutes increment.
the default time recommended by the energy star program is 15 minutes.
28. setting brightness
the blinking item is the one selected.
29. confirming imprinter installation
